SCIENCE
Hemp fibre made concrete about 30% stronger in bending and pulling, a study in India finds
Researchers tested eleven doses of hemp fibre in one concrete recipe. A dose of 1.2% gave the best resistance to cracking forces, at the cost of a stiffer wet mix.
Drafted with AI, edited by Hemp'in
Hemp'in
10 November 2026 · 3 min read

The research
Fresh and mechanical properties of hemp fiber-reinforced concrete: an experimental dosage study with multi-output artificial neural network modelling of mechanical strength was published on 1 November 2026 in Scientific Reports. The authors are K. Rajkumar and S. Anandaraj of the Department of Civil Engineering at the KPR Institute of Engineering and Technology in Coimbatore, India; Paul Oluwaseun Awoyera of Prince Mohammad Bin Fahd University in Al Khobar, Saudi Arabia; and Olaolu George Fadugba of Kabale University in Uganda. The paper is peer-reviewed and open access.
What they did
Concrete is strong when it is squeezed but weak when it is pulled or bent, so it cracks. Builders often mix in fibres, frequently synthetic ones, to hold cracks together. The researchers asked how well hemp fibre, the long fibre from the outer stem of the plant, can do that job, and how much of it to add.
They took one standard concrete recipe and changed only the amount of hemp fibre. The recipe was a common Indian grade called M30, with 340 kg of cement per cubic metre and a water to cement ratio of 0.45. The fibre was first treated with a 5% solution of sodium hydroxide, a chemical cleaning step. The fibres were long and thin: about 235 times longer than they were wide.
They made eleven mixes, from no fibre at all up to 2% of the volume, in steps of 0.2%. For each mix they first checked how easy the wet concrete was to work with. Then, after 28 days of curing, they broke three cubes, three cylinders and three beams per mix to measure three kinds of strength, following the Indian standard test method.
They also trained a computer model, an artificial neural network, to predict all three strengths from the fibre dose, and compared it with simpler curve-fitting methods.
What they found
The amount of fibre made a clear difference to all three strengths, the paper reports.
- Compressive strength, how much crushing the concrete can take, was highest at 0.6% fibre: 32.8 MPa (megapascals, a unit of pressure), 5.8% more than plain concrete. Doses from 0.4 to 0.8% were statistically just as good.
- Splitting tensile strength, how well it resists being pulled apart, peaked at 1.2% fibre: 3.95 MPa, or 33.9% more than plain concrete.
- Flexural strength, how well a beam resists bending, also peaked at 1.2%: 5.50 MPa, or 31.0% more.
There was a trade-off. The more fibre, the stiffer the wet concrete. Slump, a simple test of how much fresh concrete sags, fell from 95 mm to 40 mm across the range. A vibration test of workability went from 3 seconds to 20 seconds.
On doses the model had not seen, the neural network predicted the measured averages closely, within a few tenths of a megapascal. But a simpler curve-fitting method was equally or more accurate. The authors conclude that the network is best used to explore the response curve, not to replace real tests.
Their recommendation is a dose of about 0.6 to 1.2% hemp fibre.
What it means, and what it doesn't
For builders, the finding is practical: a small amount of plant fibre gave a sizeable gain in the strengths that matter for cracking. Crushing strength rose a little too, at its best dose of 0.6%.
The reach is limited, and the paper is open about some of it. This is one laboratory study, with one concrete recipe, one fibre treatment and three samples per mix for each test. All results are at 28 days. The abstract does not report how the concrete behaves over years, in wet or salty conditions, or whether the natural fibre keeps its strength inside the alkaline cement over time. The authors also generated extra data rows from their measurements to train the model, and they kept those separate from the 33 real results for each property.
It is a lab result, not a building code. We only report research and make no promises.
Words to know
MPa (megapascal): a unit of pressure; concrete strength is usually given in it.
Slump: how far a cone of fresh concrete sags; a lower number means a stiffer mix.
Flexural strength: how much bending a concrete beam takes before it breaks.
Neural network: a computer model that learns a pattern from examples.
How did this land?
Ask the desk
The conversation
Open in LIFENo one has replied yet. Start the conversation.
WRITE FOR HEMP'IN
Have a story from the hemp industry?
Join Hemp'in and publish your own articles to everyone who reads News.
MORE FROM HEMP'IN NEWS

A rubbery coating let recycled plastic hold up to 60% hemp hurd and soak up far less water
Hemp'in · 17 November 2026

900 changes later: what 46 days of building Hemp'in looks like
Hemp'in · 17 November 2026

A wall's direction mattered more than its insulation, a year in an old French building shows
Hemp'in · 16 November 2026