SCIENCE
A rubbery coating let recycled plastic hold up to 60% hemp hurd and soak up far less water
Troy University researchers coated hemp hurd before mixing it into recycled polyethylene. At 60% hurd, the parts were stronger and took up 58% less water than uncoated ones.
Drafted with AI, edited by Hemp'in
Hemp'in
17 November 2026 · 3 min read

The research
Interfacial Engineering of Highly Filled Recycled Polyethylene/Hemp Hurd Composites through Elastomer Pre-Coating was published on 12 November 2026 in ACS Polymers Au. The authors are Aboulfazl Barati, Zhiyong U. Wang, Alexander Lawrence Jensen, Montana Thomas Hance, Evy Aracely Ortiz and Hayden Scott Harville, all of Troy University in Alabama, United States. The paper is peer-reviewed and open access.
What they did
One way to use less new plastic is to mix recycled plastic with plant material. Hemp hurd, the woody core of the stem, is a renewable filler. The trouble, the authors explain, is that plastic and plant particles do not get on well: one is soft and water-repelling, the other stiff and water-loving. When a lot of hurd goes in, the mix flows badly when melted and the finished part tends to break early.
The team tried a simple fix: coat the hurd particles with a thin layer of elastomer, a rubbery plastic, before mixing them into recycled high-density polyethylene (the plastic of many milk jugs and pipes). They did this without chemically treating the hurd and without adding reactive bonding agents, two common alternatives.
They first compared three commercial elastomers (Nordel 4520, Engage 8180 and Vistamaxx 6202) at two coating levels, in composites with 5% hurd by weight. Engage 8180 gave the best balance of strength, stiffness and impact resistance, so they took it forward and tested composites with up to 60% hurd.
They then looked at the material from many angles: microscope images of broken surfaces, several tests of its chemistry and crystal structure, how it flows when melted, how strong it is, and how much water it soaks up.
What they found
The coating helped, at high hurd content, the paper reports. With 60% hurd by weight, compared with the same mix without coating:
- Tensile strength, how hard you can pull before it breaks, rose from 6.44 to 8.13 MPa (megapascals, a unit of pressure).
- Impact strength, how well it takes a sudden blow, rose from 9.12 to 12.90 kJ per square metre.
- Water uptake after a week (168 hours) under water fell by 58.1%.
Under the microscope, more plastic stayed stuck to the coated hurd, and cracks ran less along particle edges. The chemical tests found no new chemical bonds and no real change in the plastic's crystal structure. What changed was the flow: the coating made the melted mix less resistant to the particles and let stress ease faster.
From this, the authors propose a mechanism: small rubbery zones around the particles soften the join between plastic and hurd, so stress can spread out, without needing a full rubber shell around each particle.
What it means, and what it doesn't
For anyone making parts from recycled plastic and hemp, the attraction is that a single extra coating step allowed composites that are up to 60% hemp by weight, with better strength and much less water uptake than the uncoated version.
The limits are worth stating. The abstract compares the coated composite only with the uncoated one, not with plain recycled polyethylene or with commercial wood-plastic products, so how it ranks for real uses is not shown here. This is a lab study with one recycled plastic. The abstract gives no figures on cost, long-term weathering, or recycling the composite again. The mechanism is described by the authors as proposed.
We only report research and make no promises.
Words to know
Composite: a material made by combining two or more different materials.
Elastomer: a rubbery, stretchy plastic.
HDPE: high-density polyethylene, a common, tough plastic.
Tensile strength: how much pulling force a material takes before it breaks.
How did this land?
Ask the desk
The conversation
Open in LIFENo one has replied yet. Start the conversation.
WRITE FOR HEMP'IN
Have a story from the hemp industry?
Join Hemp'in and publish your own articles to everyone who reads News.
MORE FROM HEMP'IN NEWS

900 changes later: what 46 days of building Hemp'in looks like
Hemp'in · 17 November 2026

A wall's direction mattered more than its insulation, a year in an old French building shows
Hemp'in · 16 November 2026

Hemp oil and ground hurd did not improve wet alfalfa silage, but orange powder did, a study finds
Hemp'in · 15 November 2026