Hemp'in News

SCIENCE

Six batches of Australian hemp hurd differed far more than their size labels suggest, a study finds

Melbourne researchers measured six hurd feedstocks used for hempcrete and boards, and propose a fuller way to describe hurd than fine, coarse or mixed.

Drafted with AI, edited by Hemp'in

Hemp'in

12 November 2026 · 3 min read

The research

Physical, morphological and chemical variability of industrial hemp hurd feedstocks for biocomposite manufacture was published on 10 November 2026 in the Journal of Wood Science. The authors are Johannes Fehrmann and Benoît Belleville of the School of Agriculture, Food and Ecosystem Sciences at the University of Melbourne; Pooria Pasbakhsh and Priyan Mendis of the university's Department of Infrastructure Engineering; and Ken Dods of SAGE Research and Development in Western Australia. The paper is peer-reviewed and open access.

What they did

Hemp hurd is the woody inner core of the hemp stem, left over once the outer fibre is stripped off. It is light, and it is the main ingredient in hempcrete and in other lightweight boards and composites.

Suppliers usually sell hurd by size class: fine, coarse, mixed. The researchers asked whether that label tells a manufacturer enough. If two bags called "fine" behave differently, the boards made from them may come out differently too.

They took six hurd feedstocks from Australia: a mixed hurd, two fine fractions, two coarse fractions and a mix of hurd and fibre. Then they measured each one in many ways:

  • bulk density, how much a loosely filled volume weighs;
  • sieve analysis, shaking the hurd through meshes to sort particles by size;
  • removable fibre, how much stray fibre is still mixed in;
  • image analysis of the particles in two dimensions, and close-up pictures with a scanning electron microscope;
  • chemistry, including ash (the mineral part left after burning), plant fibre content and how acidic a hot-water extract is.

What they found

The six feedstocks varied widely, the paper reports:

  • Bulk density ranged from 74.2 to 115.7 kg per cubic metre.
  • Removable fibre went from none at all up to 8.14%.
  • The median particle size (called D50, the size half the particles are smaller than) ran from 1.42 to 3.46 mm, and the spread of sizes varied about threefold (a normalised span of 0.82 to 2.59).
  • Ash ranged from 1.4 to 9.1%, plant fibre content (measured as neutral detergent fibre) from 73.5 to 90.1%, and the extract pH from 5.80 to 6.76, all mildly acidic.

The key finding is that materials with the same label were not the same. The two fine fractions packed differently, carried different amounts of fibre and had particles of different regularity. The two coarse fractions had similar median lengths but very different particle shapes. The hurd and fibre mix stood apart: lots of fibre, low density, a wide range of sizes, and more ash and nitrogen.

The authors conclude that size class alone is not enough to specify hurd quality. From their measurements they built a trait map and propose a first classification and reporting framework, combining density, fibre content, size distribution, particle shape and a few chemical markers.

What it means, and what it doesn't

For people who make hempcrete, boards or other hurd composites, this points to a practical step: ask for more than a size class when buying hurd, and match the hurd to the binder used. For hemp processors, we infer that a common way of describing hurd could help buyers trust a batch.

The reach has limits. The study covers six feedstocks, all from Australia. It describes the materials themselves; the abstract does not report making boards or hempcrete from them, so how much each difference changes a finished product is not shown here. The authors call their classification provisional: an early version, not yet a standard.

We only report research and make no promises.

Words to know

Hurd (or shiv): the woody inner core of the hemp stem.
Bulk density: the weight of a loosely filled volume of material.
D50: the particle size that half of the particles fall below.
Biocomposite: a material made by binding plant particles or fibres together.

How did this land?

Ask the desk

Questions go privately to the desk.

The conversation

Open in LIFE

No one has replied yet. Start the conversation.

WRITE FOR HEMP'IN

Have a story from the hemp industry?

Join Hemp'in and publish your own articles to everyone who reads News.

MORE FROM HEMP'IN NEWS