SCIENCE
Adding some hemp fibre to hempcrete made it insulate better, an Ottawa study finds
Engineers at the University of Ottawa mixed fibre back into hemp-lime. The walls kept heat in better, handled humidity better, and could mean less processing.
Hemp'in
9 November 2026 · 3 min read

The research
Impact of hemp fiber content and length on the hygrothermal, mechanical, and CO2 emission performance of hemp-lime composites, by Osamah Ibrahim Mahmood (University of Ottawa and University of Samarra), Miroslava Kavgic and Martin Noël (University of Ottawa). Published in the Journal of Building Engineering, April 2026. Peer-reviewed and open access: anyone can read the full paper at the link.
What they did
Hemp-lime, often called hempcrete, is a building material made by mixing lime, water and the woody inner core of the hemp stalk, called shiv or hurd. It is used for walls and insulation. Usually only the shiv goes in. The long outer fibres are stripped off first, in a step called decortication, and sold separately.
The Ottawa team asked a simple question: what happens if you leave some of that fibre in? They made hemp-lime samples with 0%, 10%, 20% and 40% fibre, and with fibres cut to four lengths, from about 1 mm up to 25 mm. The authors describe it as the first controlled study of fibre content and length in hemp-lime. They then measured four things:
- how easily heat passes through the material (thermal conductivity);
- how much heat it stores (specific heat capacity);
- how well it soaks up and releases moisture from the air (moisture buffering);
- how much weight it takes before it crushes (compressive strength).
They also estimated the carbon dioxide (CO₂) emissions of the different mixes.
What they found
- Better insulation. Thermal conductivity fell from 0.068 to 0.053 W/(m·K) as fibre went from 0% to 40%. A lower number means less heat escapes through the wall. The authors put it at up to 20% better.
- Better humidity control. Moisture buffering rose from 2.12 to 2.73 g/m²·%RH. In plain words, the material takes up more water vapour when a room is damp and gives it back when it dries. The paper reports a gain of up to 24% in low-density mixes.
- Fibre length barely mattered. Longer fibres improved insulation by up to about 4% at most, and the authors note that this sits within the normal spread of their measurements.
- Lower strength, still usable. Adding fibre made the samples weaker under compression. The authors say strength stayed comparable to insulation boards, which are not load-bearing either.
- Lower emissions. Using a less purified shiv, with fibre still in it, could cut the mix's CO₂ emissions by up to 40.74%, by the authors' estimate.
What it means, and what it doesn't
Hempcrete is already valued for insulation and for handling moisture. This study suggests a less refined raw material could do the job as well or better. If that holds outside the lab, processors might not need to separate fibre from shiv as fully for building-grade material. That could make hempcrete simpler and cheaper to supply, though that last point is our inference, not something the paper tested.
The limits matter too. These were laboratory samples, not walls in real buildings through real winters. The strength loss means fibre-rich mixes suit infill and insulation, not structural walls. The CO₂ figure is an estimate for the material, not a full life-cycle study of a building. Building codes, long-term durability and how the mixes behave on a building site are all still open questions.
Words to know
Shiv (hurd): the woody core of the hemp stalk. Decortication: separating the outer fibre from the core. Moisture buffering: how well a material evens out indoor humidity.
How did this land?
Ask the desk
The conversation
Open in LIFENo one has replied yet. Start the conversation.
WRITE FOR HEMP'IN
Have a story from the hemp industry?
Join Hemp'in and publish your own articles to everyone who reads News.
MORE FROM HEMP'IN NEWS

A wall's direction mattered more than its insulation, a year in an old French building shows
Hemp'in · 16 November 2026

Hemp oil and ground hurd did not improve wet alfalfa silage, but orange powder did, a study finds
Hemp'in · 15 November 2026

Hemp hurd processor Tiger Fiber files for Chapter 11 and keeps operating
Hemp'in · 14 November 2026